RVVP 3x1.0mm² Braided Shielded Control Cable Anti-interference for Electromagnetic Actuators

RVVP 3x1.0mm² Braided Shielded Control Cable Anti-interference for Electromagnetic Actuators

Cable Designation & Meaning

Construction: Three 1.0 mm² fine-stranded copper conductors, PVC insulation on each core, laid up together, tinned copper braid shield (≥80% coverage) over the laid-up cores, PVC outer sheath.

Applicable Standards

• GB/T 5023.5-2008 / IEC 60227-5 — Polyvinyl chloride insulated cables — Flexible cables (cords)
• GB/T 3956-2008 / IEC 60228 — Conductors of insulated cables (Class 5 flexible)
• GB/T 18380.3 / IEC 60332-3 — Flame retardant (Category A/B/C as specified)
• GB/T 5023.2-2008 / IEC 60227-2 — Test methods

RVVP 3×1.0 mm² — Flexible Shielded Signal+Power Cable — Specification 

1. Overview & Ratings

RVVP 3×1.0 is a 3-core shielded signal+power cable rated 300/500 V. It uses pure annealed bare copper (not tinned) for both the conductor and braid, maximizing conductivity. The three 1.0 mm² cores are laid up in a triangular formation and combine signal transmission with small power capacity — enough for 3-wire sensors over longer runs and small solenoid valves. The braid suppresses EMI/RFI from nearby VFDs and motors. OD ≈ 8.5 mm, ≈ 72 kg/km (est.), ≈ 6–8 A. Max conductor temperature 70 °C, -15 to +70 °C. Intended for dry indoor signal and small-power circuits; for damp or outdoor duty, specify tinned copper variant.

2. Construction Stack (Inner → Outer, expanded)

3. Electrical Characteristics

DC resistance ≤ 19.5 Ω/km at 20 °C per GB/T 3956 Class 5 pure copper — roughly 25% lower than 0.75 mm², allowing longer sensor runs. Rated voltage 300/500 V. Estimated ampacity ≈ 6–8 A in free air at 30 °C. Insulation resistance ≥ 20 MΩ·km. Routine AC withstand test at 2000 V for 5 minutes. Typical capacitance ≈ 140 pF/m at 1 kHz. The pure copper braid provides ≈ 60–70 dB shielding at 30–1000 MHz. Voltage drop ≈ 1.95 V per 100 m at 10 A — suitable for 24 V DC sensor power runs up to 30–50 m.

Insulation & Sheath Data

Electrical Parameters

Reference values: RVVP 3×1.0 at 7 A per core, 24 V DC → max load ≈ 168 W​ per core (control/signal use). At 230 V AC → max load ≈ 1,610 VA​ per core (not recommended for power).

4. Thermal & Flame Behaviour

Operating range -15 to +70 °C continuous. Short-circuit withstand up to 160 °C for ≤ 5 seconds. PVC insulation and jacket are flame-retardant per IEC 60332-1. The cable is halogen-containing (PVC), emitting HCl gas on burning — avoid in enclosed switchrooms. For public or enclosed spaces, specify LSZH alternatives. The 0.9 mm Type ST jacket is oil-resistant for panel and machine wiring. Note: bare pure copper oxidizes in humid environments — install in dry indoor or conduit-protected locations. UV resistance is limited.

Temperature Characteristics

Fire Performance (RVVP — PVC, Non-Low-Smoke)

5. Installation Practice & Handling

Minimum bending radius ≥ 6×OD ≈ 51 mm for fixed installation; 12×OD ≈ 102 mm for drag-chain applications. The 8.5 mm OD and 72 kg/km make the cable easy to route in control panels, through conduits and along machine frames. When terminating, connect the braid shield to earth at one end (or both ends per system design) using a shield gland or drain wire. Use small ferrules on the 32-strand conductors. Route the cable away from high-power motor cables by at least 200 mm. After installation, verify insulation resistance, shield continuity and 3-wire polarity before energizing.

Mechanical & Installation Parameters

6. Typical Service Applications

3-wire pressure and temperature sensors over longer runs (20–50 m), 4–20 mA transducer interconnection, small solenoid valve and actuator power, PLC I/O signal wiring with auxiliary power, and interconnection between control panels and field instruments. The 1.0 mm² cross-section carries slightly more current than 0.75 mm², suiting applications where one core must power a small solenoid or sensor heater while the other two carry signal and ground. Particularly suitable near variable-frequency drives, servo motors and welding equipment, where the braid shield suppresses electromagnetic interference. Not for: mains AC power distribution, high-speed fieldbus, direct burial, or outdoor UV-exposed runs.

7. Testing & Quality Assurance Regime

Routine tests (100% production): DC resistance, AC voltage withstand (2000 V/5 min), insulation resistance, conductor construction, wall thickness, dimensional check, print legibility, mass per length, visual appearance, and packing. Type tests (per batch / material change): shield coverage, heat aging (100 °C/7 days), cold bend (-15 °C), jacket tensile, flame retardancy, and shielding effectiveness. Every coil ships with mill test certificate, ROHS and REACH declarations. The 300/500 V rating uses a 2000 V withstand test.

Cable Parameters

Cable Test Parameters

Cable Cross Section Structure

Construction Description

8. Factory Advantages

Pure annealed copper conductor at 32×0.20 mm stranding delivers maximum conductivity with Class 5 flexibility. Lower DC resistance (19.5 vs 26.0 Ω/km) supports longer sensor runs. 0.6 mm insulation and 0.9 mm jacket balance slimness with durability. Pure copper braid at ≈ 85% coverage provides low transfer impedance. 3-core triangular lay-up combines signal, power and ground in one cable. Colour-coded cores prevent wiring errors. 100% routine electrical QA on every reel. Cut-to-length on coils with sealed ends. Lightweight ≈ 72 kg/km. Full traceability with MTC and certification support for industrial automation tenders.

9. Packaging, Storage & Logistics

Cut to customer-specified length on export-grade coils, with both ends heat-sealed to prevent moisture ingress. Coils wrapped in waterproof film and corrugated cardboard, labelled with product type, core count, cross-section, length, weight, production date and reel number. Standard lengths 100/200/500/1000 m. Store dry indoor, -10 to +40 °C, below 75% RH, away from direct sunlight and chemical solvents. FOB Shanghai/Nanjing/Qingdao; CIF and DAP available. Sample lead time 5–7 days; bulk production 15–25 days. The light weight makes courier shipment practical.

10. Procurement Specification

State cable designation "RVVP 3×1.0 pure copper", required length per coil, and core colour preference (e.g. brown/blue/yellow-green for 3-wire sensors). Request the routine AC withstand test record (2000 V) and shield coverage certificate for the specific batch. Note that this is a pure copper (bare) signal+power variant for dry indoor use — for damp or outdoor applications, specify the tinned copper variant. Specify any regional certification requirements (UL 2464, CE, etc.) at order time. Payment: 30% T/T deposit, balance against B/L copy. Documents: MTC, ROHS/REACH, COO, commercial invoice, packing list.

11. Cable Industry FAQ

Q1: Why choose 1.0 mm² over 0.75 mm²? Lower DC resistance (19.5 vs 26.0 Ω/km), higher ampacity (6–8 A vs 4–6 A), and enough current capacity for small solenoid valves and longer sensor runs.

Q2: Can it power small solenoid valves? Yes — the 1.0 mm² core can carry 6–8 A, enough for small solenoid valves and sensor heaters while the other two cores handle signal and ground.

Q3: How long can the sensor run be? At 24 V DC and 10 A load, voltage drop is ≈ 1.95 V per 100 m — suitable for runs up to 30–50 m with acceptable voltage loss.

Q4: What is the voltage rating? 300/500 V, suitable for low-voltage signal and small-power circuits.

Q5: Why pure copper instead of tinned? Bare pure copper has higher conductivity than tinned copper, ideal for low-level signal and small-power circuits where every ohm matters.

Q6: Is it suitable for outdoor use? No — limited UV resistance and bare copper oxidize in humidity. Use indoors or in UV-protected conduits.

Q7: How do you ground the shield? Connect braid to earth at one end (or both ends per system design) using a shield gland or drain wire.

Q8: What is the bending radius? ≥ 6×OD ≈ 51 mm for fixed; 12× for moving applications.

Q9: What is the temperature range? -15 to +70 °C continuous.

Q10: What proof ships? Routine AC test record (2000 V) + shield coverage certificate + MTC.

Q11: When should I step up to 3×1.5? For larger solenoid valves, longer runs (50+ m), or higher current loads (10+ A), step up to RVVP 3×1.5 mm².